• Model 63110A/ 63113A/63115A LED Load Simulator
Key Features:
  • Unique LED mode for LED power driver test
  • Programmable LED dynamic resistance (Rd)
  • Programmable internal resistance (Rr) for simulating LED ripple current
  • Fast response for PWM dimming test
  • Up to eight channels in one mainframe
  • 16-bit precision voltage and current measurement with dual-range
  • Full Protection: OC, OP, OT protection and OV alarm

rencontre extraterrestre wiki

follow url As a constant current source, the LED driver has an output voltage range with a constant output current. LED drivers are usually tested in one of the following ways:

  • With LEDs
  • Using resistors for loading
  • Using Electronic Loads in Constant Resistance (CR) mode, or Constant Voltage (CV) mode 

carbon dating radiometric dating However all these testing methods each have their own disadvantages.

source site As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating 
resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to 
simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver 
to not start up due to the difference in V-I characteristic between the resistors and the LEDs. 
When using Electronic Loads, the CR and CV mode settings are set for when the LED is 
under stable operation and therefore, is unable to simulate turn on or PWM brightness control 
characteristics. This may cause the LED driver to function improperly or trigger it’s protection 
circuits. These testing requirements can be achieved when using a LEDs as a load; however, 
issues regarding the LED aging as well as different LED drivers may require different types of 
LEDs or a number of LEDs. This makes it inconvenient for mass production testing. 

http://www.mentzer-consult.de/?afinoes=broker-bin%C3%A4re-optionen-test&1c9=5c Chroma has created the industries first LED operating mode for simulating LED loading with our 63110A load model from our 6310A series Electronic Loads. By setting the LED driver's output voltage, and current, the Electronic Load can simulate the LED’s loading characteristics. The LED’s forward voltage and operating resistance can also be set to further adjust the loading current and ripple current to better simulate LED characteristics. The 63110A design also has increased bandwidth to allow for PWM dimming testing. 

forex samurai download Figure 2 shows the current waveform from a LED load. Figure 3 shows the current waveform from 63110A's LED mode load function. From figures 2 and 3, the start up voltage and current of the LED driver is very similar. Figure 4 shows the dimming current waveform of the LED. Figure 5 shows the dimming current waveform when using 63110A as a load. 

binäre optionen ab 1 euro
The internal resistance (Rr) can be adjusted to simulate the LED driver output ripple current. The traditional E-load can not simulate the ripple current of LED shown as Figure 6. Figure 7 shows the ripple current waveform from a LED load. Figure 8 shows the ripple current waveform from the 63110A LED mode load function. 

site de rencontre tchat gratuit Figure 9 shows the current waveform from a resistive load. Figure 10 shows the current waveform from a CR mode of an Electronic Load loading. Figure 9 and 10 current waveform differs significantly from that of LED loading, especially the voltage and current overshoot, which may cause the LED driver to go into protection. Using resistive load or CR mode to test LED drivers may cause the LED drivers to fail to turn on as shown in Figure 11. 

Skriv en recension

Obs: HTML översätts inte!
    Dålig           Bra

Model 63110A/ 63113A/63115A LED Load Simulator

  • Varumärke: CHROMA
  • Artikelnummer: 6311XA
  • Lagerstatus: 6 - 8 Veckor
Broschyr / Brochure

LabVIEW driver
go to site Open Link

  • 0 kr


Tillgängliga val